A BEGINNER'S GUIDE TO PLUMBING FOR BATHTUB INSTALLATION

A Beginner's Guide to Plumbing for Bathtub Installation

A Beginner's Guide to Plumbing for Bathtub Installation

Blog Article

Call Today

In this article down the page you can discover a bunch of professional expertise with regards to How to Install a Bathtub Yourself.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a tub isn't precisely rocket science, but it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a new one is also a moderately difficult task. If the old bathtub is conveniently accessible, the task can move quickly; if you need to open a wall to get rid of the old bathtub and also place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to leave the old tub as well as embeded in the new one. Ensure you have qualified yourself for the job and fit attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This short article will certainly aid you mount a brand-new tub in your washroom if you have actually already bought a brand-new bathtub and also don't require to change the arrangement of your previous water pipes.
Your devices and product checklist need to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Preparing for the Installation


    First of all, the supporting structure supplied with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to prevent stress on the tub.
    Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use all of the provided washers.
    Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last placement.

    Removing Old Touches


    If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted accessibility that is frequently the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
    Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Mounting the Bath tub


    Utilizing both wood boards under its feet, put the bathtub in the called for position. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
    The next objective is to make sure that the bath tub is leveled all round. This can be attained by checking the level and readjusting the feet on the bath tub till the level checks out degree.
    To mount faucets, fit all-time low of the outermost adaptable tap connector to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
    Switch on the supply of water as well as inspect all joints and new pipework for leakages and tighten them if needed. Fill the bathtub and likewise check the overflow outlet and the typical outlet for leakages.
    Finally, deal with the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bathtub should wait up until the bath tub has been used at the very least once as this will resolve it into its last setting.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next, place the faucet in the placing hole in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet adapters. The former type must be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the bath tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this activity prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant glue as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We had been guided to that editorial about Installing A Bathtub through a friend on our other blog. Are you aware of another person who is excited by the topic? Why not promote it. Kudos for your time. Come back soon.


    Request Estimate

    Report this page